Discovering Plumbing Basics is Crucial for Installing a Bathtub
Discovering Plumbing Basics is Crucial for Installing a Bathtub
Blog Article
We have stumbled upon the article involving Tools You Need to Install a New Bathtub below on the internet and believe it made good sense to relate it with you on my blog.
Mounting a bathtub isn't specifically rocket science, yet it does require solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old tub with a new one is also a reasonably challenging job. If the old bathtub is readily easily accessible, the job can move rapidly; if you have to open a wall surface to get rid of the old tub and also place the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly need a helper to move out the old tub and set in the brand-new one. See to it you have actually certified on your own for the task and fit attempting it. Rather than working with a specialist to take over a halfway-completed job, it is far better to think about employing one prior to you begin. Opportunities are you might need a professional plumber to make tube connections.
This short article will help you install a new bath tub in your bathroom if you have currently bought a brand-new bathtub and don't require to change the setup of your previous water system pipelines.
Your tools and material checklist need to comprise the following:
Planning for the Installment
To start with, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to avoid stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to currently be ready to be suited its last setting.
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you ought to do is disconnect the water supply. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite bothersome due to the limited access that is often the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. Once the supply pipes have actually been removed, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Prior to proceeding to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Utilizing the two wood boards under its feet, position the bathtub in the required position. The wood boards are practical in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 small points.
The next goal is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bathtub until the level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap adapter to the suitable supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Turn on the water supply as well as inspect all joints as well as new pipework for leaks as well as tighten them if needed. Fill up the bath tub as well as additionally check the overflow outlet and the normal electrical outlet for leakages.
Lastly, take care of the bath paneling as described in the manufacturer's user's manual. Tiling and sealing around the bathtub needs to wait until the tub has been made use of a minimum of when as this will settle it right into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipelines.
If you need to fit a monobloc, then you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washers are in area in between the tap and the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the tap is firmly in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The previous kind ought to be attached to the tap ends first, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a rigid seal, creating the water to pass through the wall in between the bathroom and also the tiling, bring about complications with wetness and possible leakages to the ceiling below.
You can select from a range of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealant can break relatively very early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily available on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very taken with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you enjoyed my blog posting. Kindly set aside a second to promote this article if you enjoyed reading it. Thank you for taking the time to read it.
Get A Free Estimate Report this page